Single function · Civils

Series 1H+

Height limitation for machines with two or three-piece booms.

The Series 1H+ works like our Series 1H height limiter, with a sensor on each boom section. This makes it the better choice for larger machines.

Not sure which system you need? Use our System Finder
GKD Series 1H+ height restrictor control unit

2 or 3

Boom sections, each with its own sensor

Self-install

Designed to be fitted by your own team

Push button

In-cab display with integrated key switch

Valve or relay

Motion cut output at the height limit

How it works

You set the limit. The system does the rest.

The operator sets a height limit on the display. A sensor on each boom section tracks the whole boom, and the Series 1H+ cuts the lift circuit before any part of it goes above the limit.

01 · ST

Push button display with key switch

A simple push button display fitted in the cab. The operator sets the limit with the buttons, and the integrated key switch keeps the settings secure.

02 · DT

A sensor on each boom section

A gravity-referenced angle sensor on every boom section means the whole boom is monitored, not just the first section. The limit stays accurate when the machine is working on a slope.

03 · LIMIT

Motion cut output

At the limit, the system cuts the lift circuit. Machines with pilot hydraulics use a valve, and machines with electric controls use a relay. The output can also drive an external alarm or beacon.

Where it works

Built for a wide range of job applications

Machine types

  • Machines with two piece booms
  • Machines with three piece booms
  • Tracked excavators
  • Wheeled excavators
  • Other articulated boom machines

Job applications

  • Working under overhead power lines
  • Working beneath bridges and tunnels
  • Indoor demolition and strip-out
  • Sites with low-clearance access
  • Restricted-height yards and depots
GKD Series 1 height limiter on a wheeled excavator boom

The Series 1H+ brings Series 1H height limiting to every section of a two or three piece boom.

Compatibility

Made for two and three piece booms

The Series 1H+ is a standalone height limiter with a sensor on each boom section and its own display. It cuts movement through a hydraulic solenoid valve on the lift circuit.

  • Larger machines with two or three piece booms
  • Relay output drives a hydraulic solenoid valve, or an external alarm or beacon
  • A gravity-referenced sensor on each boom section keeps the limit accurate on a slope
  • Single piece boom? The Series 1H is the simpler choice
  • LED display in the cab with integrated key switch
  • Working near the railway? Choose the Series 2HS Evo or Series 2LHS Evo

Installation

Fit it yourself, or let us do it

The Series 1H+ is suitable for self-installation. If you would rather leave it to us, our engineers and approved partners can fit the system, set it up and show your operators how it works.

01

Fit

Mount an angle sensor on each boom section and the display in the cab, then wire the output to a hydraulic solenoid valve on the lift circuit.

02

Set the limit

Set the height limit on the display. The key switch keeps the setting secure.

03

Work

A sensor on each boom section tracks the whole boom, and the system cuts the lift circuit before any part of it goes above the limit.

04

Maintain

Book an annual inspection with us to keep the system working as it should.

Talk to us about the Series 1H+

Tell us about your machines and where they work, and we will help you choose the right system. Call +44 (0) 1202 861961 or send us a message.

Send us a message

Fill in your details and our team will get back to you.

FAQ

Series 1H+ questions

When do I need Series 1H+ instead of Series 1H?

The Series 1H monitors a single boom. The Series 1H+ has a sensor on each boom section, so it monitors and restricts every part of a two or three piece boom. That makes it much better suited to larger machines.

Will the height limit drift if the machine is on a slope?

No. The angle sensors are gravity-referenced rather than referenced to the machine body, so the height limit stays accurate when the machine is working on an incline.

Can I install the Series 1H+ myself?

Yes. The Series 1H+ is suitable for self-installation. If you prefer, our engineers and approved partners can fit it for you.

Can it warn people outside the cab?

Yes. As well as cutting hydraulic movement, the relay output can drive an external alarm or beacon.

Is Series 1H+ Network Rail approved?

No. For work near the running line, choose the Series 2HS Evo or Series 2LHS Evo, which are Network Rail approved.

Other civils products

Compare with the rest of the range

Series 1H height limiter system

Single function

Series 1H

Height limitation to protect from overhead obstacles or danger.

View product →
GKD Series 1 safety control systems

Combined function

Series 1HS

Combined height and slew control for smaller machines.

View product →
GKD Series 2 integrated safety control systems

Combined function · Rail certified

Series 2HS Evo

Advanced height and slew control with Network Rail approval.

View product →